Application must be submitted to your Distributor within 30 days of repair

Warranty Claim Form

Dealer Information (Contractor/HVAC Company)

Dealer Account Name *

CE Dealer Account# *

Distributor # *

Select your Region/Distributor # *

Name *

First

Last

Email *

Customer Information (End-user/Equipment Owner/Homeowner)

Homeowner/Owner Name *

First

Last

Homeowner/Owner Address *

Address Line 1

Address Line 2

City

State

Zip Code

Warranty Type

Warranty Type *

Standard
Stock Unit
Bulletin
Service Parts
Competitive Equipment
Preauthorization
Unit Exchange
Opt. Contract (PARTS ONLY)

Application Type

Application Type *

Owner Occupied Residential
Other Residential Application
Commercial
Installing Homeowner

Installing Homeowner *

Unit Information

Model # *

Serial # *

Equipment Install Date *

Equipment Fail Date *

Equipment Repair Date *

Optional Contract # (PARTS ONLY)

Service Bulletin/Pre-Authorization #

Parts Information

How many different parts do you need to submit for this unit? *

1st Part Information

FAILED Part

Causal Part *

This is the part that caused the initial failure (only one part applies)

Old Carrier Part # *

(Not Vendor #)

Order/Invoice #

Part S # (if applicable)

Install Date *

REPLACEMENT/NEW Part

New Carrier Part # *

(Not Vendor #)

Order/Invoice # *

Part S # (if applicable)

Install Date *

2nd Part Information

2nd FAILED Part

Causal Part *

This is the part that caused the initial failure (only one part applies)

Old Carrier Part # *

(Not Vendor #)

Order/Invoice #

Part S # (if applicable)

Install Date *

2nd REPLACEMENT/NEW Part

New Carrier Part # *

(Not Vendor #)

Order/Invoice # *

Part S # (if applicable)

Install Date *

3rd Part Information

3rd FAILED Part

Causal Part *

This is the part that caused the initial failure (only one part applies)

Old Carrier Part # *

(Not Vendor #)

Order/Invoice #

Part S # (if applicable)

Install Date *

3rd REPLACEMENT/NEW Part

New Carrier Part # *

(Not Vendor #)

Order/Invoice # *

Part S # (if applicable)

Install Date *

4th Part Information

4th FAILED Part

Causal Part *

This is the part that caused the initial failure (only one part applies)

Old Carrier Part # *

(Not Vendor #)

Order/Invoice #

Part S # (if applicable)

Install Date *

4th REPLACEMENT/NEW Part

New Carrier Part # *

(Not Vendor #)

Order/Invoice # *

Part S # (if applicable)

Install Date *

5th Part Information

5th FAILED Part

Causal Part *

This is the part that caused the initial failure (only one part applies)

Old Carrier Part # *

(Not Vendor #)

Order/Invoice #

Part S # (if applicable)

Install Date *

5th REPLACEMENT/NEW Part

New Carrier Part # *

(Not Vendor #)

Order/Invoice # *

Part S # (if applicable)

Install Date

Quality Information

DOA Labor Repair Type *

(Labor Allowance is based on the selection of a Labor Repair Type)

Causal Code *

Select the main component that failed and the failure mode.

Accumulator Failure Modes *

Contamination – A101
Leak – A102
Restricted – A103

Actuator Failure Modes *

Gears Stripped – A201
Stuck – A202
Will not run – A203

Blower Assembly Failure Modes *

Motor failure – grounded – B201
Motor failure – open – B202
Motor failure – shorted – B203
Motor failure – noise/vibration – B204
Motor failure – thermal tripping – B205
Motor failure – wont start – B206
Motor failure – incorrect speed – B207
Mounting Issue – B208
Noise – B209
Vibration – B210
Wheel Failure – separation – B211
Wheel Failure – noise/vibration – B212

Blower Housing Failure Modes *

Corrosion – B301
Damaged – B302

Blower Shaft/Bearing Failure Modes *

Grind Shaft – B401
Loose Locking Collar – B402
Vibration – B403

Blower Wheel Failure Modes *

Separation – B501
Noise – B502
Vibration – B503
Wrong Rotation – B504

Breaker Failure Modes *

Shorted – B601

Burner, Assy, Pilot Failure Modes *

Cracked – B701
Flame retainer issue – B702
No ignition – B703
Soot – B704
Ass’y Flame roll out – B801
Ass’y Poor Combustion – B802
Ass’y Soot – B803
Pilot Dirty orifice – B901
Pilot No ignition – B902
Pilot No thermocouple output – B903
Pilot not sensing – B904

Capacitor/Hard Start Failure Modes *

Brunt – C101
Closed – C102
Open – C103
Ruptured – C104
Swelled – C105
Wrong size – C106
HS Capacitor – H201
HS PTC Failure – H202
HS Relay Failure – H203
HS Wiring – H204

Check Valve Failure Modes *

Rattling – C201
Restricted – C202
Stuck – C203

Coil Related Failure Modes *

Damage – C301
Leak – Braze Joint – C302
Leak – Corrosion – C303
Leak – Crack – C304
Leak – Fin Pack – C305
Leak – Puncture – C306
Restricted – C307

Collector Box Failure Modes *

Leak – C401
Plugged – C402

Compressor Failure Modes *

Excess cycling – C501
Leak – C502
Noise – C503
Wiring plug – burnt – C504
Wiring plug – change out – C505
Wiring plug – open circuit – C506
Wiring plug – rub – C507
Won’t Pump – C508
Won’t Shift – C509
Won’t Start – C510
Wrong Capacity – C511
Wrong Voltage – C512

Condensate Pan Failure Modes *

Broken bottom fitting – C601
Horizontal pan broken – C602
Leak – C603
Missing/deformed fitting – C604
Vertical pan broken – C605

Condensate Trap Failure Modes *

No pressure switch output – C128
Not Communicating – C129
Not pulling in contactor – C130
Not staging properly – C131
Shorted terminal strip – C132
Water damage – C133

Contactor Failure Modes *

Burnt – C901
Chattering – C902
Open – C903
Shorted – C904
Terminal Damage – C905

C BD, Cntl Bd/Term str, Mtr contr., Inv cnt VFD Failure Modes *

Motor will not shut off – C111
Burnt/open traces – C112
Compressor not operating – C113
Defrost cycle issue – C114
Failed Relays – C115
Motor not operating – C116
Fault code incorrect / wont clear – C117
Improper unit recognition – C118
Inducer will not shut off – C119
Mis-wired – C120
No accessory output – C121
No cooling blower – C122
No flame sensor – C123
No gas valve output – C124
No heating blower – C125
No HSI output – C126
No inducer output – C127
No pressure switch output – C128
Not communication – C129
Not pulling in contactor – C130
Not staging properly – C131
Shorted term strip – C132
Water damage – C133

Control Valve Failure Modes *

Not Loading – C141
Not unloading – C142

Crankcase Heater Failure Modes *

Grounded – C151
Open – C152
Shorted – C153
Temperature Switch Failure – C251

Coupling Box Failure Modes *

Cold spot baffle – Leak – C161
Cold spot baffle – Missing – C162
Cold spot baffle – Whistling – C163

Damper Failure Modes *

Bad Switch – D101
Harness miswired – D102
Will not close – D103
Will not open – D104

Electric Heat Failure Modes *

Burnt connectors – E101
Burnt wires – E102
Element open – E103
Element shorted – E104

Enhancement Module Failure Modes *

Plastic damage/crack – E201

Filter Drier Failure Modes *

Compressor replacement – F101
Leak repair – F102
Restricted – F103
System repair – F104
Choice 29
Choice 28

Gas Baffle Failure Modes *

Soot – G101

Gas Valve Failure Modes *

Leak – G201
Shorted – G202
Will not close – G203
Will not open – G204

Generator Part Failure Modes

Oil Leak – G031
Wont start – G302
Wont transfer – G303
Wont produce power – G304
Noise – G306
Corrosion – G307

Primary/Secondary Heat Exchanger Failure Modes *

Oil Leak -Corrosion – H301
Cracked – H302
Flue cover panel – H303
Hole/Void – H304

Hot water coil Failure Modes *

Leak – H501
Restricted – H502

Ignitor Failure Modes *

Alignment issue – J101
Broken – J102
Open – J103
Shorted – J104

Inducer Assembly Failure Modes *

Hall effect sensor – J201
Leak – J202
Motor failure – J203
Mounting issue – J204
Noise – J205
Vibration – J206
Wheel failure – J207

Inducer Wheel Failure Modes *

Bent – J301
Broken – J302
Corrosion – J303

Labor Only *

Compressor – L101
Motor failure – L102
Leak – L103
Unit change out – L104
Inspection – L105
Minor component – L106
Concession – L107

Limit Switch Failure Modes *

Stuck closed – L201
Stuck open – L202
Missing shield – L203

Motor Failure Modes *

Bearing issues – M101
Grounded – M102
Incorrect speed – M103
Noise – M104
Open – M105
Prop failure/seized to shaft – M106
Shorted – M107

Muffler Failure Modes *

Leak – M301

Orifice/Capillary Failure Modes *

Corrosion – K101
Wrong size installed – K102
Restricted – K103

Outdoor Fan Failure Modes *

Blade cracks – K201
Blade imbalance – K202
Hub loose – K203
Motor fail/seized to shaft – K204
Noise – K205
Vibration – K206

Piston Failure Modes *

Incorrect size – P201
Missing – P202
Plugged – P203

Power Supply Failure Modes *

No power – P301
Intermittent power/light _ P302

Pressure Switch Failure Modes *

Failed stuck open – P401
Leak – P402
Wiring – P403
Wrong location – P404

PTAC plug Failure Modes *

Incorrect plug – P501
Plug issue – P502

Pulley Failure Modes *

Corrosion – P601
Cracked – P602
Loose – P603

Pump Failure Modes *

Float stuck – P701
Leak – P702
Seized – P703
Will not pump – P704

Relay Failure Modes *

Burnt – R101
Chattering – R102
Open – R103
Shorted – R104

Relief Valve Failure Modes *

Leak – R201

Remote Control Failure Modes *

Not communicating – R301

Reversing Valve Failure Modes *

Leak – R401
Noise – R402
Pilot Tube Leak – R403
Slow Shift – R404
Solenoid failure – R405
Won’t Shift – R406

Service Valve Failure Modes *

Adapter connection issue – S101
Leak – S102
Seized stem – S103
Stripped stem – S104
Stuck / broken valve core – S105

Solenoid Failure Modes *

Chattering – S201
Leak – S202
Open – S203
Shorted -S204
Valve stuck closed – S205
Valve stuck open – S206

Smoke Detector Failure Modes *

Defective – S301
Internal short – S302
Not sensing – S303
Repeated alarm fault – S304

Switch Mechanical Failure Modes *

Will not close – S401
Will not open – S402

Sensors, Def, Hall, Enthaply, Flame Failure Modes *

Hall Inducer mtr failure – H101
Hall No feedback to IGC board – H102
Enthalpy – No 2nd stage cooling – E301
Enthalpy – not switching – E302
Enthalpy – will not energize – E303
Defrost sensor – no call for heat – D201
Defrost sensor – not energizing fan relay – D202
Defrost sensor – not sensing – D203
Defrost sensor – open – D204

Temperature/Pressure Gauge Failure Modes *

Out of calibration – T101
Leak – T102

Temperature Switch Failure Modes *

Out of range – T201
Stuck closed – T202
Stuck open – T203

Thermistor Failure Modes *

Cracked – T401
Resistance out of range – T402
Wiring issue – T403

Tstat, Aquastat, Freezestat, SAMod Failure Modes *

Blinking display – T601
Broken pigtail – T602
No back light – T603
Not controlling properly – T604
Not staging correctly – T605
Won’t power up – T606
SAM fail to communicate – S501
SAM won’t power up – S502
Freezestat Faulty- F301
Freezestat Malfunction – F302
Freezestat Stuck open – F303
Aquastat Hi limit – stuck closed – A402
Aquastat Hi limit – stuck open – A403
Aquastat no relay output – A404

Transformer Failure Modes *

Noise – T701
Odor/hot – T702
Open – T703
Shorted – T704

Diagnosis/Service Performed: *

Please provide a detailed description of how the part failed and what diagnostic steps were used to determine the failure mode.

Any supporting documentation you would like to add?

Click or drag files to this area to upload. You can upload up to 5 files.

Are you working with a Customer Assurance Manager on a Case? *

Please select which Customer Assurance Manager you are working with. *

Case# (Salesforce Case#)

Please provide this if you have it. This would have been created when you spoke with the Customer Assurance Manager.

Signature *

Clear Signature

Please use your mouse to sign.

Submit date *

A copy of this form will be emailed to you for your records.

Save and Resume Later

Your form entry has been saved and a unique link has been created which you can access to resume this form.

Enter your email address to receive the link via email. Alternatively, you can copy and save the link below.

Please note, this link should not be shared and will expire in 30 days, afterwards your form entry will be deleted.

Copy Link

Email *